Gladiator GAJG36GRDG Instruction Manual download pdf (Page 4)

ASSEMBLY INSTRUCTIONS

Cabinet Use Requirements

■ Intended for use in a garage.

■ Maximum weight limit is 50 lbs (22.7 kg) for each shelf.

■ Maximum weight limit is 300 lbs (136 kg) for the cabinet.

Unpack Cabinet Parts

1. Remove and verify the contents. Contents include a hex key, a

key, and the parts and fasteners shown in “Parts.”

2. Dispose of/recycle all packaging materials.

Assemble Cabinet

Gather the required tools before starting installation.

Tools Needed

Tools Supplied

IMPORTANT:

■ Two people may be required to complete the assembly.

■ As you assemble the cabinet, make sure the edges with the

holes are facing up.

■ If you are assembling the cabinet on the floor, fasten the eight

front corner bolts, two at each corner, after you stand the cabinet

upright.

1. Place side panel (P1) on a flat, firm surface so that the edge with

the holes is facing up as shown.

2. Insert the cabinet top (P2) between the edges of side panel (P1).

NOTE: Make sure the edges with the holes are facing up.

3. Align the holes and attach the top (P2) to side panel (P1) using

hex-head bolts (F1) and the three ⁵⁄₁₆"

flange nuts (F2) as shown.

Do not tighten completely.

4. Position the other side panel (P1) so that the top (P2) is between

the edges of side panel (P1).

5. Align the holes and attach the top (P2) to the side (P1) using hex-

head bolts (F1) and the three ⁵⁄₁₆"

flange nuts (F2) as shown. Do

not tighten completely.

6. Insert the cabinet bottom (P3) between the edges of the side

panels (P1).

NOTE: Make sure the edges with the holes are facing up.

7. Align the holes and attach the bottom (P3) to the sides (P1) using

hex-head bolts (F1) and the three ⁵⁄₁₆" flange nuts (F2). Do not

tighten completely.

Attach Back Panels

IMPORTANT:

■ Attach the back panels starting at the top of the cabinet with

back panel (AAA) and working down to the cabinet bottom. Each

back panel will overlap the panel below.

■ Do not completely tighten the screws until all back panels are in

place.

1. Align back panel (AAA) with the holes in the cabinet top. Using

Phillips-head screws (F3c), attach back panel (AAA) to the

cabinet top and sides.

2. Slide the top of back panel (BBB) under the bottom of back panel

(AAA). Using Phillips-head screws, fasten back panel (BBB) to

the cabinet sides.

3. Repeat Step 2 for the remaining back panels ending with back

panel (EEE).

4. Using Phillips-head screws, attach each back panel to the panel

below.

NOTE: Using Phillips-head screws, attach panel (EEE) to the

cabinet bottom (P3).

5. Completely tighten all back panel screws starting with the sides

and continuing with the top, middle and bottom.

6. Using the hex key (provided), completely tighten all cabinet bolts

and nuts.

F1 F2

⁵⁄₁₆

" hex-head bolt (28)

⁵⁄₁₆

" flange nut (12)

■ ¹⁄₂" wrench

■ Phillips screwdriver

■ Level

■ Hex key ■ Key

WARNING

Excessive Weight Hazard

Use two or more people to move, assemble or install

cabinet.

Failure to do so can result in back or other injury.

F3c

Phillips-head screw (34)

1 2 3 4 5 6 7 8 9 ... 19 20

Comments to this Manuals

No comments

Gladiator GAJG36GRDG Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for AV equipment stands Gladiator GAJG36GRDG